# generated by Slic3r 1.2.9 on Sat Dec  3 18:04:37 2016

[filament:ABS_0.3mm]
bed_temperature = 110
bridge_fan_speed = 40
cooling = 0
disable_fan_first_layers = 3
extrusion_multiplier = 1.1
fan_always_on = 0
fan_below_layer_time = 20
filament_colour = #FFFFFF
filament_diameter = 3,7
first_layer_bed_temperature = 145
first_layer_temperature = 270
max_fan_speed = 40
min_fan_speed = 20
min_print_speed = 10
slowdown_below_layer_time = 8
temperature = 260

[filament:ABS_0.4mm]
bed_temperature = 110
bridge_fan_speed = 40
cooling = 0
disable_fan_first_layers = 3
extrusion_multiplier = 1.1
fan_always_on = 0
fan_below_layer_time = 20
filament_colour = #FFFFFF
filament_diameter = 3,7
first_layer_bed_temperature = 145
first_layer_temperature = 270
max_fan_speed = 40
min_fan_speed = 20
min_print_speed = 10
slowdown_below_layer_time = 8
temperature = 260

[filament:ABS_0.5mm]
bed_temperature = 110
bridge_fan_speed = 40
cooling = 0
disable_fan_first_layers = 3
extrusion_multiplier = 1.05
fan_always_on = 0
fan_below_layer_time = 20
filament_colour = #FFFFFF
filament_diameter = 3,7
first_layer_bed_temperature = 145
first_layer_temperature = 270
max_fan_speed = 40
min_fan_speed = 20
min_print_speed = 10
slowdown_below_layer_time = 8
temperature = 260

[filament:HIPS_0.3mm]
bed_temperature = 120
bridge_fan_speed = 25
cooling = 1
disable_fan_first_layers = 5
extrusion_multiplier = 1.1
fan_always_on = 1
fan_below_layer_time = 20
filament_colour = #FFFFFF
filament_diameter = 3,7
first_layer_bed_temperature = 135
first_layer_temperature = 265
max_fan_speed = 20
min_fan_speed = 5
min_print_speed = 10
slowdown_below_layer_time = 8
temperature = 260

[filament:HIPS_0.4mm]
bed_temperature = 120
bridge_fan_speed = 25
cooling = 1
disable_fan_first_layers = 5
extrusion_multiplier = 1.1
fan_always_on = 1
fan_below_layer_time = 20
filament_colour = #FFFFFF
filament_diameter = 3,7
first_layer_bed_temperature = 135
first_layer_temperature = 265
max_fan_speed = 20
min_fan_speed = 5
min_print_speed = 10
slowdown_below_layer_time = 8
temperature = 260

[filament:HIPS_0.5mm]
bed_temperature = 120
bridge_fan_speed = 25
cooling = 1
disable_fan_first_layers = 5
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 20
filament_colour = #FFFFFF
filament_diameter = 3,7
first_layer_bed_temperature = 135
first_layer_temperature = 265
max_fan_speed = 20
min_fan_speed = 5
min_print_speed = 10
slowdown_below_layer_time = 8
temperature = 260

[filament:PLA_0.3mm]
bed_temperature = 55
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 3
extrusion_multiplier = 1.1
fan_always_on = 1
fan_below_layer_time = 60
filament_colour = #FFFFFF
filament_diameter = 3,7
first_layer_bed_temperature = 60
first_layer_temperature = 230
max_fan_speed = 100
min_fan_speed = 20
min_print_speed = 20
slowdown_below_layer_time = 8
temperature = 230

[filament:PLA_0.4mm]
bed_temperature = 55
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 3
extrusion_multiplier = 1.1
fan_always_on = 1
fan_below_layer_time = 60
filament_colour = #FFFFFF
filament_diameter = 3,7
first_layer_bed_temperature = 60
first_layer_temperature = 230
max_fan_speed = 100
min_fan_speed = 20
min_print_speed = 20
slowdown_below_layer_time = 8
temperature = 230

[filament:PLA_0.5mm]
bed_temperature = 55
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 3
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 60
filament_colour = #FFFFFF
filament_diameter = 3,7
first_layer_bed_temperature = 60
first_layer_temperature = 230
max_fan_speed = 100
min_fan_speed = 20
min_print_speed = 20
slowdown_below_layer_time = 8
temperature = 215

[presets]
filament = ABS_0.3mm.ini
print = 
printer = RF1000_ABS_0.4mm.ini

[print:ABS_0.100Layer]
avoid_crossing_perimeters = 0
bottom_solid_layers = 5
bridge_acceleration = 0
bridge_flow_ratio = 1.1
bridge_speed = 30
brim_width = 0
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_speed = 50%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 10%
fill_pattern = rectilinear
first_layer_acceleration = 0
first_layer_extrusion_width = 0
first_layer_height = 0.35
first_layer_speed = 70%
gap_fill_speed = 5
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 30
interface_shells = 0
layer_height = 0.1
min_skirt_length = 15
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 30
perimeters = 2
post_process = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 6
skirt_height = 1
skirts = 3
small_perimeter_speed = 10
solid_infill_below_area = 10
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 30
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 20
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0.3
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 6
support_material_speed = 30
support_material_threshold = 50
thin_walls = 1
threads = 4
top_infill_extrusion_width = 100%
top_solid_infill_speed = 20
top_solid_layers = 8
travel_speed = 80

[print:ABS_0.125Layer]
avoid_crossing_perimeters = 0
bottom_solid_layers = 4
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 30
brim_width = 10
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_speed = 70%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.6
fill_angle = 45
fill_density = 20%
fill_pattern = rectilinear
first_layer_acceleration = 0
first_layer_extrusion_width = 0
first_layer_height = 0.35
first_layer_speed = 60%
gap_fill_speed = 10
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 30
interface_shells = 0
layer_height = 0.125
min_skirt_length = 15
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 30
perimeters = 2
post_process = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 6
skirt_height = 1
skirts = 0
small_perimeter_speed = 25
solid_infill_below_area = 10
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 30
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 20
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0.3
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 6
support_material_speed = 30
support_material_threshold = 50
thin_walls = 1
threads = 2
top_infill_extrusion_width = 100%
top_solid_infill_speed = 25
top_solid_layers = 6
travel_speed = 130

[print:ABS_0.200Layer]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 25
brim_width = 10
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_speed = 70%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.6
fill_angle = 45
fill_density = 20%
fill_pattern = rectilinear
first_layer_acceleration = 0
first_layer_extrusion_width = 0
first_layer_height = 0.35
first_layer_speed = 60%
gap_fill_speed = 10
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 30
interface_shells = 0
layer_height = 0.2
min_skirt_length = 15
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 30
perimeters = 2
post_process = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 6
skirt_height = 1
skirts = 0
small_perimeter_speed = 25
solid_infill_below_area = 10
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 30
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 20
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0.3
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 6
support_material_speed = 30
support_material_threshold = 50
thin_walls = 1
threads = 2
top_infill_extrusion_width = 100%
top_solid_infill_speed = 20
top_solid_layers = 5
travel_speed = 130

[print:ABS_0.300Layer]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 30
brim_width = 10
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_speed = 70%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.6
fill_angle = 45
fill_density = 20%
fill_pattern = rectilinear
first_layer_acceleration = 0
first_layer_extrusion_width = 0
first_layer_height = 0.35
first_layer_speed = 60%
gap_fill_speed = 10
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 30
interface_shells = 0
layer_height = 0.3
min_skirt_length = 15
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 30
perimeters = 2
post_process = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 6
skirt_height = 1
skirts = 0
small_perimeter_speed = 25
solid_infill_below_area = 10
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 30
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 20
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0.3
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 6
support_material_speed = 30
support_material_threshold = 50
thin_walls = 1
threads = 2
top_infill_extrusion_width = 100%
top_solid_infill_speed = 25
top_solid_layers = 3
travel_speed = 130

[print:HIPS_0.200Layer]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 35
brim_width = 5
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_speed = 65%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.6
fill_angle = 45
fill_density = 20%
fill_pattern = rectilinear
first_layer_acceleration = 0
first_layer_extrusion_width = 0
first_layer_height = 0.35
first_layer_speed = 60%
gap_fill_speed = 10
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 35
interface_shells = 0
layer_height = 0.2
min_skirt_length = 15
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 35
perimeters = 3
post_process = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 6
skirt_height = 1
skirts = 0
small_perimeter_speed = 30
solid_infill_below_area = 10
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 35
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 20
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0.3
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 6
support_material_speed = 35
support_material_threshold = 50
thin_walls = 1
threads = 2
top_infill_extrusion_width = 100%
top_solid_infill_speed = 30
top_solid_layers = 4
travel_speed = 130

[print:PLA_0.100Layer]
avoid_crossing_perimeters = 0
bottom_solid_layers = 5
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 15
brim_width = 5
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_speed = 70%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 20%
fill_pattern = rectilinear
first_layer_acceleration = 0
first_layer_extrusion_width = 0
first_layer_height = 0.35
first_layer_speed = 60%
gap_fill_speed = 15
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 45
interface_shells = 0
layer_height = 0.1
min_skirt_length = 15
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 45
perimeters = 2
post_process = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 6
skirt_height = 1
skirts = 0
small_perimeter_speed = 40
solid_infill_below_area = 10
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 40
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 20
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0.3
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 6
support_material_speed = 45
support_material_threshold = 50
thin_walls = 1
threads = 2
top_infill_extrusion_width = 220%
top_solid_infill_speed = 35
top_solid_layers = 8
travel_speed = 130

[print:PLA_0.125Layer.ini]
avoid_crossing_perimeters = 0
bottom_solid_layers = 6
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 15
brim_width = 0
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_speed = 70%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 10%
fill_pattern = rectilinear
first_layer_acceleration = 0
first_layer_extrusion_width = 0
first_layer_height = 0.35
first_layer_speed = 60%
gap_fill_speed = 15
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 45
interface_shells = 0
layer_height = 0.125
min_skirt_length = 15
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 45
perimeters = 2
post_process = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 6
skirt_height = 1
skirts = 0
small_perimeter_speed = 40
solid_infill_below_area = 10
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 40
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 20
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0.3
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 6
support_material_speed = 45
support_material_threshold = 50
thin_walls = 1
threads = 2
top_infill_extrusion_width = 220%
top_solid_infill_speed = 35
top_solid_layers = 6
travel_speed = 130

[print:PLA_0.150Layer.ini]
avoid_crossing_perimeters = 0
bottom_solid_layers = 4
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 15
brim_width = 5
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_speed = 70%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 20%
fill_pattern = rectilinear
first_layer_acceleration = 0
first_layer_extrusion_width = 0
first_layer_height = 0.35
first_layer_speed = 60%
gap_fill_speed = 15
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 45
interface_shells = 0
layer_height = 0.15
min_skirt_length = 15
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 45
perimeters = 2
post_process = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 6
skirt_height = 1
skirts = 0
small_perimeter_speed = 40
solid_infill_below_area = 10
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 40
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 20
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0.3
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 6
support_material_speed = 45
support_material_threshold = 50
thin_walls = 1
threads = 2
top_infill_extrusion_width = 220%
top_solid_infill_speed = 35
top_solid_layers = 5
travel_speed = 130

[print:PLA_0.200Layer]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 15
brim_width = 5
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 70%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 20%
fill_pattern = rectilinear
first_layer_acceleration = 0
first_layer_extrusion_width = 0
first_layer_height = 0.35
first_layer_speed = 60%
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
infill_speed = 50
interface_shells = 0
layer_height = 0.2
max_print_speed = 80
max_volumetric_speed = 0
min_skirt_length = 15
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 50
perimeters = 2
post_process = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 6
skirt_height = 1
skirts = 0
small_perimeter_speed = 45
solid_infill_below_area = 10
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 50
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 20
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0.3
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 6
support_material_speed = 50
support_material_threshold = 50
thin_walls = 1
threads = 2
top_infill_extrusion_width = 215%
top_solid_infill_speed = 40
top_solid_layers = 4
travel_speed = 130
xy_size_compensation = 0

[printer:RF1000_ABS_0.3mm]
bed_shape = 0x0,245x0,245x230,0x230
before_layer_gcode = 
end_gcode = M104 S0\nM140 S0\nG91\n; retract filament\nG1 E-2 F300\n; Output Object\nM400\nM3079\nM400\n;Steppers off\nM84                                            \n;Acceleration to default...\n;Acc printing\nM201 X1000 Y1000 Z1000\n;Acc travel\nM202 X1000 Y1000 Z1000
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode = 
nozzle_diameter = 0.3
octoprint_apikey = 
octoprint_host = 
pressure_advance = 0
retract_before_travel = 1
retract_layer_change = 1
retract_length = 2
retract_length_toolchange = 10
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 25
start_gcode = ;--------------------------------------\nG28 ; home all axes\nG1 Z5 F500 ; lift nozzle\nM109 S[first_layer_temperature] ; wait for extruder temp to be reached\nM3001 ; Aktivate Z-Compensation \n; Move Z-axis n-steps up (see manual)\n;M3004 S0 ; + n-steps bed down // - n-steps bed up! old Firmware Version <= 0.91.48\n;M3006 S0 ; configure the static z-offset (units are [um])\nG90 ; use absolute coordinates\nM82 ; use absolute distances for extrusion\nG92 E0 ; start line\nG1 F300 E-0.5\nG1 X230 Y22 Z0.35 F5000\nG1 F800 E13\nG1 X20 E25 F1000\n; Acceleration up to...\n; Acc printing\nM201 X3000 Y3000 Z100\n; Acc travel\nM202 X3000 Y3000 Z100\n; ZJERK \nM205 Z0.1\n;--------------------------------------
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
vibration_limit = 0
wipe = 0
z_offset = 0

[printer:RF1000_ABS_0.4mm]
bed_shape = 0x0,245x0,245x230,0x230
before_layer_gcode = 
end_gcode = M104 S0\nM140 S0\nG91\n; retract filament\nG1 E-2 F300\n; Output Object\nM400\nM3079\nM400\n;Steppers off\nM84                                            \n;Acceleration to default...\n;Acc printing\nM201 X1000 Y1000 Z1000\n;Acc travel\nM202 X1000 Y1000 Z1000
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode = 
nozzle_diameter = 0.4
octoprint_apikey = 
octoprint_host = 
pressure_advance = 0
retract_before_travel = 1
retract_layer_change = 1
retract_length = 2
retract_length_toolchange = 10
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 25
start_gcode = ;--------------------------------------\nG28 ; home all axes\nG1 Z5 F500 ; lift nozzle\nM109 S[first_layer_temperature] ; wait for extruder temp to be reached\nM3001 ; Aktivate Z-Compensation \n; Move Z-axis n-steps up (see manual)\n;M3004 S0 ; + n-steps bed down // - n-steps bed up! old Firmware Version <= 0.91.48\n;M3006 S0 ; configure the static z-offset (units are [um])\nG90 ; use absolute coordinates\nM82 ; use absolute distances for extrusion\nG92 E0 ; start line\nG1 F300 E-0.5\nG1 X230 Y22 Z0.35 F5000\nG1 F800 E13\nG1 X20 E25 F1000\n; Acceleration up to...\n; Acc printing\nM201 X3000 Y3000 Z100\n; Acc travel\nM202 X3000 Y3000 Z100\n; ZJERK \nM205 Z0.1\n;--------------------------------------
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
vibration_limit = 0
wipe = 0
z_offset = 0

[printer:RF1000_ABS_0.5mm]
bed_shape = 0x0,245x0,245x230,0x230
end_gcode = M104 S0\nM140 S0\nG91\n; retract filament\nG1 E-2 F300\n; Output Object\nM400\nM3079\nM400\n;Steppers off\nM84                                            \n;Acceleration to default...\n;Acc printing\nM201 X1000 Y1000 Z1000\n;Acc travel\nM202 X1000 Y1000 Z1000
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode = 
nozzle_diameter = 0.5
retract_before_travel = 1
retract_layer_change = 1
retract_length = 2
retract_length_toolchange = 10
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 25
start_gcode = ;--------------------------------------\nG28 ; home all axes\nG1 Z5 F500 ; lift nozzle\nM109 S[first_layer_temperature] ; wait for extruder temp to be reached\nM3001 ; Aktivate Z-Compensation \n; Move Z-axis n-steps up (see manual)\n;M3004 S0 ; + n-steps bed down // - n-steps bed up! old Firmware Version <= 0.91.48\n;M3006 S0 ; configure the static z-offset (units are [um])\nG90 ; use absolute coordinates\nM82 ; use absolute distances for extrusion\nG92 E0 ; start line\nG1 F300 E-0.5\nG1 X230 Y22 Z0.35 F5000\nG1 F800 E13\nG1 X20 E25 F1000\n; Acceleration up to...\n; Acc printing\nM201 X3000 Y3000 Z100\n; Acc travel\nM202 X3000 Y3000 Z100\n; ZJERK \nM205 Z0.1\n;--------------------------------------
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
vibration_limit = 0
wipe = 0
z_offset = 0

[printer:RF1000_HIPS_0.3mm]
bed_shape = 0x0,245x0,245x230,0x230
before_layer_gcode = 
end_gcode = M104 S0\nM140 S0\nG91\n; retract filament\nG1 E-2 F300\n; Output Object\nM400\nM3079\nM400\n;Steppers off\nM84                                            \n;Acceleration to default...\n;Acc printing\nM201 X1000 Y1000 Z1000\n;Acc travel\nM202 X1000 Y1000 Z1000
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode = 
nozzle_diameter = 0.3
octoprint_apikey = 
octoprint_host = 
pressure_advance = 0
retract_before_travel = 1
retract_layer_change = 1
retract_length = 1
retract_length_toolchange = 10
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 20
start_gcode = ;--------------------------------------\nG28 ; home all axes\nG1 Z5 F500 ; lift nozzle\nM109 S[first_layer_temperature] ; wait for extruder temp to be reached\nM3001 ; Aktivate Z-Compensation \n; Move Z-axis n-steps up (see manual)\n;M3004 S0 ; + n-steps bed down // - n-steps bed up! old Firmware Version <= 0.91.48\n;M3006 S0 ; configure the static z-offset (units are [um])\nG90 ; use absolute coordinates\nM82 ; use absolute distances for extrusion\nG92 E0 ; start line\nG1 F300 E-0.5\nG1 X230 Y22 Z0.35 F5000\nG1 F800 E13\nG1 X20 E25 F1000\n; Acceleration up to...\n; Acc printing\nM201 X3000 Y3000 Z100\n; Acc travel\nM202 X3000 Y3000 Z100\n; ZJERK \nM205 Z0.1\n;--------------------------------------
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
vibration_limit = 0
wipe = 0
z_offset = 0

[printer:RF1000_HIPS_0.4mm]
bed_shape = 0x0,245x0,245x230,0x230
before_layer_gcode = 
end_gcode = M104 S0\nM140 S0\nG91\n; retract filament\nG1 E-2 F300\n; Output Object\nM400\nM3079\nM400\n;Steppers off\nM84                                            \n;Acceleration to default...\n;Acc printing\nM201 X1000 Y1000 Z1000\n;Acc travel\nM202 X1000 Y1000 Z1000
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode = 
nozzle_diameter = 0.4
octoprint_apikey = 
octoprint_host = 
pressure_advance = 0
retract_before_travel = 1
retract_layer_change = 1
retract_length = 1
retract_length_toolchange = 10
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 20
start_gcode = ;--------------------------------------\nG28 ; home all axes\nG1 Z5 F500 ; lift nozzle\nM109 S[first_layer_temperature] ; wait for extruder temp to be reached\nM3001 ; Aktivate Z-Compensation \n; Move Z-axis n-steps up (see manual)\n;M3004 S0 ; + n-steps bed down // - n-steps bed up! old Firmware Version <= 0.91.48\n;M3006 S0 ; configure the static z-offset (units are [um])\nG90 ; use absolute coordinates\nM82 ; use absolute distances for extrusion\nG92 E0 ; start line\nG1 F300 E-0.5\nG1 X230 Y22 Z0.35 F5000\nG1 F800 E13\nG1 X20 E25 F1000\n; Acceleration up to...\n; Acc printing\nM201 X3000 Y3000 Z100\n; Acc travel\nM202 X3000 Y3000 Z100\n; ZJERK \nM205 Z0.1\n;--------------------------------------
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
vibration_limit = 0
wipe = 0
z_offset = 0

[printer:RF1000_HIPS_0.5mm]
bed_shape = 0x0,245x0,245x230,0x230
end_gcode = M104 S0\nM140 S0\nG91\n; retract filament\nG1 E-2 F300\n; Output Object\nM400\nM3079\nM400\n;Steppers off\nM84                                            \n;Acceleration to default...\n;Acc printing\nM201 X1000 Y1000 Z1000\n;Acc travel\nM202 X1000 Y1000 Z1000
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode = 
nozzle_diameter = 0.5
retract_before_travel = 1
retract_layer_change = 1
retract_length = 1
retract_length_toolchange = 10
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 20
start_gcode = ;--------------------------------------\nG28 ; home all axes\nG1 Z5 F500 ; lift nozzle\nM109 S[first_layer_temperature] ; wait for extruder temp to be reached\nM3001 ; Aktivate Z-Compensation \n; Move Z-axis n-steps up (see manual)\n;M3004 S0 ; + n-steps bed down // - n-steps bed up! old Firmware Version <= 0.91.48\n;M3006 S0 ; configure the static z-offset (units are [um])\nG90 ; use absolute coordinates\nM82 ; use absolute distances for extrusion\nG92 E0 ; start line\nG1 F300 E-0.5\nG1 X230 Y22 Z0.35 F5000\nG1 F800 E13\nG1 X20 E25 F1000\n; Acceleration up to...\n; Acc printing\nM201 X3000 Y3000 Z100\n; Acc travel\nM202 X3000 Y3000 Z100\n; ZJERK \nM205 Z0.1\n;--------------------------------------
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
vibration_limit = 0
wipe = 0
z_offset = 0

[printer:RF1000_PLA_0.3mm]
bed_shape = 0x0,245x0,245x230,0x230
before_layer_gcode = 
end_gcode = M104 S0\nM140 S0\nG91\n; retract filament\nG1 E-2 F300\n; Output Object\nM400\nM3079\nM400\n;Steppers off\nM84                                            \n;Acceleration to default...\n;Acc printing\nM201 X1000 Y1000 Z1000\n;Acc travel\nM202 X1000 Y1000 Z1000
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode = 
nozzle_diameter = 0.3
octoprint_apikey = 
octoprint_host = 
pressure_advance = 0
retract_before_travel = 1
retract_layer_change = 1
retract_length = 1
retract_length_toolchange = 10
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 16
start_gcode = ;--------------------------------------\nG28 ; home all axes\nG1 Z5 F500 ; lift nozzle\nM109 S[first_layer_temperature] ; wait for extruder temp to be reached\nM3001 ; Aktivate Z-Compensation \n; Move Z-axis n-steps up (see manual)\n;M3004 S0 ; + n-steps bed down // - n-steps bed up! old Firmware Version <= 0.91.48\n;M3006 S0 ; configure the static z-offset (units are [um])\nG90 ; use absolute coordinates\nM82 ; use absolute distances for extrusion\nG92 E0 ; start line\nG1 F300 E-0.5\nG1 X230 Y22 Z0.35 F5000\nG1 F800 E13\nG1 X20 E25 F1000\n; Acceleration up to...\n; Acc printing\nM201 X3000 Y3000 Z100\n; Acc travel\nM202 X3000 Y3000 Z100\n; ZJERK \nM205 Z0.1\n;--------------------------------------
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
vibration_limit = 0
wipe = 0
z_offset = 0

[printer:RF1000_PLA_0.4mm]
bed_shape = 0x0,245x0,245x230,0x230
before_layer_gcode = 
end_gcode = M104 S0\nM140 S0\nG91\n; retract filament\nG1 E-2 F300\n; Output Object\nM400\nM3079\nM400\n;Steppers off\nM84                                            \n;Acceleration to default...\n;Acc printing\nM201 X1000 Y1000 Z1000\n;Acc travel\nM202 X1000 Y1000 Z1000
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode = 
nozzle_diameter = 0.4
octoprint_apikey = 
octoprint_host = 
pressure_advance = 0
retract_before_travel = 1
retract_layer_change = 1
retract_length = 1
retract_length_toolchange = 10
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 16
start_gcode = ;--------------------------------------\nG28 ; home all axes\nG1 Z5 F500 ; lift nozzle\nM109 S[first_layer_temperature] ; wait for extruder temp to be reached\nM3001 ; Aktivate Z-Compensation \n; Move Z-axis n-steps up (see manual)\n;M3004 S0 ; + n-steps bed down // - n-steps bed up! old Firmware Version <= 0.91.48\n;M3006 S0 ; configure the static z-offset (units are [um])\nG90 ; use absolute coordinates\nM82 ; use absolute distances for extrusion\nG92 E0 ; start line\nG1 F300 E-0.5\nG1 X230 Y22 Z0.35 F5000\nG1 F800 E13\nG1 X20 E25 F1000\n; Acceleration up to...\n; Acc printing\nM201 X3000 Y3000 Z100\n; Acc travel\nM202 X3000 Y3000 Z100\n; ZJERK \nM205 Z0.1\n;--------------------------------------
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
vibration_limit = 0
wipe = 0
z_offset = 0

[printer:RF1000_PLA_0.5mm]
bed_shape = 0x0,245x0,245x230,0x230
before_layer_gcode = 
end_gcode = M104 S0\nM140 S0\nG91\n; retract filament\nG1 E-2 F300\n; Output Object\nM400\nM3079\nM400\n;Steppers off\nM84                                            \n;Acceleration to default...\n;Acc printing\nM201 X1000 Y1000 Z1000\n;Acc travel\nM202 X1000 Y1000 Z1000
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode = 
nozzle_diameter = 0.5
octoprint_apikey = 
octoprint_host = 
pressure_advance = 0
retract_before_travel = 1
retract_layer_change = 1
retract_length = 1
retract_length_toolchange = 10
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 16
start_gcode = ;--------------------------------------\nG28 ; home all axes\nG1 Z5 F500 ; lift nozzle\nM109 S[first_layer_temperature] ; wait for extruder temp to be reached\nM3001 ; Aktivate Z-Compensation \n; Move Z-axis n-steps up (see manual)\n;M3004 S0 ; + n-steps bed down // - n-steps bed up! old Firmware Version <= 0.91.48\n;M3006 S0 ; configure the static z-offset (units are [um])\nG90 ; use absolute coordinates\nM82 ; use absolute distances for extrusion\nG92 E0 ; start line\nG1 F300 E-0.5\nG1 X230 Y22 Z0.35 F5000\nG1 F800 E13\nG1 X20 E25 F1000\n; Acceleration up to...\n; Acc printing\nM201 X3000 Y3000 Z100\n; Acc travel\nM202 X3000 Y3000 Z100\n; ZJERK \nM205 Z0.1\n;--------------------------------------
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
vibration_limit = 0
wipe = 0
z_offset = 0

[settings]
autocenter = 1
mode = expert